Custom Coat Federal Standard Color # 35056 Ultramarine Blue T86

CUSTOM COAT FEATURES and BENEFITS

• Easy to use, as you just mix in the hardener, shake it, and then spray, roll or brush it onto a surface!
• Waterproof, heat, and UV resistant, so it protects coated surfaces from rust and corrosion.
• A flexible textured coating that will resist chipping while providing impact protection and abrasion resistance.
• Extremely durable with excellent surface adhesion and helps deaden sounds and vibrations.
• Available with a tintable base that allows you to create your own custom color or multi-colored look.

Custom Coat Bed Liner is a premium durable long-lasting textured 1.67 VOC 2K (two-component) protective urethane coating. Custom Coat is a very versatile product that can be used for an endless amount of applications but is primarily manufactured for application onto truck beds, metal, aluminum, fiberglass, concrete, wood, and most OEM manufacturer’s finishes.

MIXING TINTABLE

Custom Coat Tintable Truck Bed Liner Coating is proportionately packaged to simply mix the tintable bed liner base, the hardener, and the tint together. Mixing Custom Coat Tintable Bed Liner Coating couldn't be easier, as the liner coating, hardener, and coloring tint are conveniently packaged separately in the required pre-measured mixing proportions, so you just need to mix the three products together, shake it, and spray it!

"p" The tintable bed liner coating comes in a convenient 1-liter can (1.06-quart size) that's partially filled with 21 fluid ounces (615 ml) of tintable liner coating (CUS TBL-QT). This leaves 11 fluid ounces of space for you to directly pour in the 8 fluid ounce (237 ml) container of hardener (CUS BLH-HP) and also pour 3 to 4 fluid ounces of solvent-based basecoat color tint. That's a full 32 fluid ounce (1 quart) can of activated and sprayable bed liner coating.

COVERAGE

• Practical Coverage: 110 - 130 square foot per 1 U.S. gallon (standard 4-quart size kit) @ 10-12 mils wet film thickness.
• A standard 4-quart (1 gallon) size liner kit on average will cover a full-size truck short bed (about 6 feet long), but 5 or 6 quarts of liner are needed on average to cover a full-size truck long bed (about 8 feet long).

COATING SPECIFICATIONS

• Bed Liner has a 3 to 1 mix ratio and is 1.67 VOC when used as packaged.
• Pot life: 45 - 60 minutes @ 72°F
• Touch dry: 1.5 hours (depending on film build) @ 72°F
• Light duty: 48 hours @ 72°F
• Regular duty: 5-7 days @ 72°F

SURFACE PREPARATION

• Clean Surface - Surface to be coated must be cleaned with high-quality wax and grease remover (Recommended surface cleaners CUS SP-522 Aerosol, KUS KW901or KUS KW912 Quarts amp; Gallons).
• Remove Surface Debris - Remove loose paint, rust, and any other debris that may affect coating adhesion.
• Sand Surface - Sand surface area with 120 to 180 grit sandpaper or with a nylon cup brush (Recommended sanding products by Dura-Gold). For hard to reach and difficult to sand areas, use red scuff pads. The whole surface should be sanded thoroughly to ensure proper coating adhesion. Re-clean and degrease the surface before priming.
• Prime Surface - Spot prime any areas where bare metal has been exposed with a suitable self-etching acid etch primer (Recommended CUS SP-440 Aerosol or CUS SEP35 Quarts amp; Gallons). All bare metal, aluminum or galvanized surfaces must be primed with an etch primer or a direct-to-metal epoxy or urethane primer to ensure optimal coating adhesion (Recommended 2K DTM Epoxy Primer CUS KEP Series Kit in Quarts, Half-Gallons amp; Gallons).
• Mask Surrounding Surface Areas - To prevent over-spray from getting on additional surface areas, mask off all areas surrounding the application area before spraying.

SPRAY APPLICATION

• Remove the cap from a mixed and activated can of bed liner coating, then attach the can to a Custom Shop Custom Coat Bed Liner Applicator Gun (CUS BLG-055). Set the air pressure at the gun between 40-70.
• Apply to a prepared surface by spraying with an even sweeping motion to obtain the texture you desire.
• Additional coats can be applied after a 45 to 60-minute flash off period between coats.
• Reducing the flash off times, having excessive film build, or spraying at reduced temperatures will retard the drying times.

Custom Coat Tintable Truck Bed Liner is also Available in a Full Spectrum of Awesome Colors:

Standard Tintable Base Colors

GM White, Bright White, Mesa Gray, Dove Gray, Shoreline Beige, Dakota Brown, Safety Yellow, Lime Green, Emerald Green, Safety Blue, Reflex Blue, Bright Purple, Safety Orange, Hot Rod Red, Blood Red, Bright Silver, Pewter Metallic, Charcoal Metallic, Tintable Metallic, and Blue Metallic

Federal Standard Color Camouflage Series Tintable Bases

34094 Olive Drab, 34052 USMC Dark Olive Drab, 34128 Woodland Green, Authentic WWII Olive Drab, 34089 Olive Green, 33303 Khaki, 30051 Camo Brown, 33105 Field Drab Brown, 30215 Light Brown, 33446 Desert Tan, 33510 Sandstone, 30480 Field Tan, 30257 Earth Yellow, 36521 Frost Beige, 25045 Insignia Blue, 35056 Ultramarine Blue, 35048 Navy Blue, 36270 Haze Gray, 36118 Battleship Dark Gray, 36375 Light Gray, 36473 Air Force Gray, 36300 Aircraft Gray, 37031 Camo Smoke Tintable, 35177 Camo Medium Blue, 30277 Sand Brown, 30266 Golden Sand and 25010 Coyote Brown